VXDIAG Scanners How to Connect Instruction Manual

VXDIAG Hardware Connection have three connection mode :
USB Connection
LAN Connection
WiFi Connection
VXDIAG USB/LAN Connection
Connect OBDII cable to the vehicle 16pin diagnostic port, and USB/LAN cable to the computer.

VXDIAG-Scanners-How-to-Connect-Instruction-Manual-1

After device boot complete, the power led will flash, and the buzzer will prompt.Install USB driver for Windows 7/8/8.1/10The first time to connect USB cable to the computer, Windows will prompt [Installing device driver] . Windows automatically complete driver installation.

VXDIAG-Scanners-How-to-Connect-Instruction-Manual-2

Install USB Driver for Windows xp
The first time to connect USB cable to the computer, Windows will prompt [Found New Hardware]

VXDIAG-Scanners-How-to-Connect-Instruction-Manual-3

Please follow these steps to complete USB driver installation.
1. Select [No, not this time], then click [Next]

VXDIAG-Scanners-How-to-Connect-Instruction-Manual-4

2.Select [Install Driver Automatically], then click [Next]

VXDIAG-Scanners-How-to-Connect-Instruction-Manual-5

3.Please wait while the wizard installs the software

VXDIAG-Scanners-How-to-Connect-Instruction-Manual-6

4.Complete Found New Hardware Wizard, click [Finish]

VXDIAG-Scanners-How-to-Connect-Instruction-Manual-7

5. Thereafter, it will pop up the second time [Found New Hardware Wizard], same as above.
6. The USB Driver installed completed

VXDIAG-Scanners-How-to-Connect-Instruction-Manual-8

After USB driver is successfully installed, PC LED will flashing.
7. Start VX Manager program,select [Device],then click [Configure], Connection Type select [Auto],click [Save],Restart VX Manager program

VXDIAG-Scanners-How-to-Connect-Instruction-Manual-9
Please make sure the device is connected.
Run VX Manager, The information of device will be displayed in “Device Manager”

VXDIAG-Scanners-How-to-Connect-Instruction-Manual-10
VXDIAG WiFi Connection
Connect OBDII cable to the vehicle 16pin diagnostic port, and computer connect to the device through WiFi.

VXDIAG-Scanners-How-to-Connect-Instruction-Manual-11

1.Click VCX-WiFi, and check [Connect automatically] ,then click [Connect]

VXDIAG-Scanners-How-to-Connect-Instruction-Manual-12

2.Setting obtain an IP address automatically

VXDIAG-Scanners-How-to-Connect-Instruction-Manual-13
VXDIAG-Scanners-How-to-Connect-Instruction-Manual-14
VXDIAG-Scanners-How-to-Connect-Instruction-Manual-15
VXDIAG-Scanners-How-to-Connect-Instruction-Manual-16
VXDIAG-Scanners-How-to-Connect-Instruction-Manual-17

3.Start VX Manager program,select [Device],then click [Configure], Connection Type select [WLAN],click [Save]

VXDIAG-Scanners-How-to-Connect-Instruction-Manual-18
VXDIAG-Scanners-How-to-Connect-Instruction-Manual-19
VXDIAG-Scanners-How-to-Connect-Instruction-Manual-20
VXDIAG-Scanners-How-to-Connect-Instruction-Manual-21
VXDIAG-Scanners-How-to-Connect-Instruction-Manual-22

4.Restart VX Manager program,computer have been connected to the device through WiFi
VXDIAG-Scanners-How-to-Connect-Instruction-Manual-23

Add Comment

Required fields are marked *. Your email address will not be published.