crack ODIS-S 4.2.3 is tested working fine with the hardware Wifi VAS6154 VAG scanner.
Here we go for the guide on install crack ODIS-S 4.2.3 on Wifi VAS6154.

VAS 6154 ODIS 4.2.3 test results:
DTC memory…OK
Identification…OK
Output Diagnostic Test Mode…OK
basic setting …OK
coding …OK
coding bus master …OK
measured values …OK
adaptation …OK
Access authorization …OK
Test on: Win7 32 bit
Connection type: both USB and Wlan.

Procedure:
Install crack ODIS-S 4.2.3 on Wifi VAS6154 in Step -by-step procedure:
Right click on “VAS6154 Driver” and select “Run as administrator”
odis-s-4-2-3-run-with-vas6154-1

Click on “Next”

Finish VAS Driver Setup Wizard.
odis-s-4-2-3-run-with-vas6154-2

Plug the interface VAS6154 to the computer and get windows message “Your device is ready to use”.
odis-s-4-2-3-run-with-vas6154-3

odis-s-4-2-3-run-with-vas6154-4

Right click on the “VAS Config” and select “Run as administrator”.
odis-s-4-2-3-run-with-vas6154-5

Click on “Firmware+”
odis-s-4-2-3-run-with-vas6154-6

Click on “Upgrade”.
odis-s-4-2-3-run-with-vas6154-7 odis-s-4-2-3-run-with-vas6154-8

Exit VAS Config.

Delete the folder of “VAS6154 Driver”.
odis-s-4-2-3-run-with-vas6154-9

Again right click on the “VAS Config” and select “Run as administrator”.

Click on the “License”, you can see Passthru, PDU, VW are all available.
odis-s-4-2-3-run-with-vas6154-10

Click on “Diagnostic”, then “VW ODIS”, then “Install”.
odis-s-4-2-3-run-with-vas6154-11

Install complete.
odis-s-4-2-3-run-with-vas6154-12

Part 1: How to use VAS6154 via USB connection.

Back to click “Configure”, then connection type “USB” and save.
odis-s-4-2-3-run-with-vas6154-13

Open “Wolkswagen”
odis-s-4-2-3-run-with-vas6154-14

Here warning and notes.
odis-s-4-2-3-run-with-vas6154-15

Welcome to Diagnosis, click on “OBD” then “Start self diagnosis”.
odis-s-4-2-3-run-with-vas6154-16

Ensure the ignition is on.
odis-s-4-2-3-run-with-vas6154-17
Here fault codes.
odis-s-4-2-3-run-with-vas6154-18

Go to option “Identification”.
odis-s-4-2-3-run-with-vas6154-19

If the ignition is off, you will get the message shown as below, just follow it to do.
odis-s-4-2-3-run-with-vas6154-20

OBD starting..
odis-s-4-2-3-run-with-vas6154-21

More functions to perform incl. Output Diagnostic Test Mode, basic setting, coding, coding bus master, measured values, adaptation, Access authorization etc.
odis-s-4-2-3-run-with-vas6154-22
Exit ODIS-S.
VAS6154 connect to the network.
odis-s-4-2-3-run-with-vas6154-23

Work network
odis-s-4-2-3-run-with-vas6154-24

Network location is now work, click on “Close”.
odis-s-4-2-3-run-with-vas6154-25

Part 2: How to use VAS6154 via Wlan connection.
Again, open “VAS Configure”, choose connection type “Wlan”.
odis-s-4-2-3-run-with-vas6154-26

Repeat the same procedure as the USB connection type to diagnose.

End.

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website