CGDI PROG BMW program F31 smart key FEM

TOPICS:CGDI Prog BMW

17-2

CGDI Prog MSV80 can program keys to BMW CAS1, CAS2, CAS3, CAS3+, FEM, BDC. Here, i will display how to use CGDI PROG BMW for F31 FEM remote programming.
Remote: 868

Chassis: F020

BMW F31 FEM

CDDI PROG can program keys to BMW CAS1, CAS2, CAS3, CAS3+, FEM, BDC. Here, i will display how to use CGDI PROG BMW for F31 FEM remote programming. Remote: 868 Chassis: F020 BMW F31 FEM 1 Voltage test platform 2 CGDI PROG BMW (this tool supports key matching and new key programming (when all keys are lost) of BMW CAS1, CAS2, CAS3, CAS3+, FEM, BDC) 3 The procedure: Run CGDI PROG BMW software on www.obd2tool.com after finish all connection Go to FEM/BDC key match 4 The current FEM BDC needs update the ECU program before performing key matching. Please ensure that the car battery has enough power. The programming process, please keep the equipment cable connection 6 Please remove the FEM BDC and then use the programmer to read and save data from the 95XXX EEPROM chip on FEM BDC computer board 7 Read the original car EEPROM data file 8 The 95128 EEPROM chip 9-11 CGDI BMW is reading the chip data 12-15 Save data 16 Use the programmer to write the calculated new data to the 95XXX EEPROM chip , then put the FEM BDC back into the car 17.18 Write M95128 19 Check the FEM connection 20 Voltage test platform is on 21 Use the programmer to write the calculated new data to the 95XXX EEPROM chip , then put the FEM BDC back into the car 22 The ECU is being programmed… 23-25 Again, write M95128 26 Again, write M95128 27 Voltage test platform should be on 28 The FEM 29 Please remove the FEM BDC and then use the CGDI programmer to write the original car EEPROM data back to 95XXX EEPROM chip and FEM BDC back into the car 30 Coding is successful!!!! 32 33 Job’s done.

Voltage test platform

17-1

CGDI PROG BMW

(this tool supports key matching and new key programming (when all keys are lost) of BMW CAS1, CAS2, CAS3, CAS3+, FEM, BDC)

17-3

The procedure:

Run CGDI PROG BMW software after finish all connection

Go to FEM/BDC key match
17-4

The current FEM BDC needs update the ECU program before performing key matching. Please ensure that the car battery has enough power. The programming process, please keep the equipment cable connection

17-5

Please remove the FEM BDC and then use the programmer to read and save data from the 95XXX EEPROM chip on FEM BDC computer board

17-6

Read the original car EEPROM data file

17-7 17-8

The 95128 EEPROM chip

17-9 17-10 17-11

CGDI BMW is reading the chip data

17-12 17-13 17-14

17-15

Save data

17-16

Use the programmer to write the calculated new data to the 95XXX EEPROM chip , then put the FEM BDC back into the car

17-17 17-18

Write M95128

17-19

Check the FEM connection

17-20

Voltage test platform is on

17-21

Use the Key Program Tool to write the calculated new data to the 95XXX EEPROM chip , then put the FEM BDC back into the car

17-22

The ECU is being programmed…

17-23 17-24 17-25

Again, write M95128

17-26

Again, write M95128
17-27

Voltage test platform should be on

17-28

The FEM

17-29

Please remove the FEM BDC and then use the CGDI programmer to write the original car EEPROM data back to 95XXX EEPROM chip and FEM BDC back into the car

17-30

Coding is successful!!!!

17-31 17-32

Job’s done.

Add Comment

Required fields are marked *. Your email address will not be published.